正交设计-紫外分光光度法测定青蒿中的青蒿素

以干青蒿叶为原料,考察石油醚萃取青蒿素的工艺条件,如温度、时间、溶剂量及超声功率等因素,正交法确定了最佳萃取工艺条件为温度40℃,超声功率90W,时间20min（两次）,液固比120∶1（mL.g-1）。紫外分光光度法直接测定不同产地青蒿中青蒿素的含量,结果表明：用超声波强化石油醚萃取青蒿素与常规浸泡法石油醚萃取比较,用超声波可以大大缩短萃取时间,提高了萃取率。     

The effects of ultrasound frequency and power on the activation energy in Si-KOH reaction system

The activation energy is the minimum amount of energy required to initiate a reaction. It is one of the important indexes for appraising a reaction. The chemical reaction rate is closely related to the value of activation energy, and reducing activation energy is propitious to promoting a chemical reaction. In the present paper, the relationship between the activation energy in Si-KOH reaction system and the ultrasound frequency and power has been discussed for the first time. The range of ultrasound frequency and power is 40-100kHz （interval by 20kHz） and 10-50W （interval by 10W）, respectively. The experimental clata indicate that the activation energy decreases with the increasing ultrasound power. Comparing with the activation energy without ultrasound irradiation, the results in our paper indicate that ultrasound irradiation could reduce the activation energy in Si-KOH reaction system and increase the reaction rate.     

Opportunities and Challenges in the Use of TiO2 Nanoparticles Modified with Citric Acid to Synthesize Advanced Nanocomposites Based on Poly(amide-imide) Containing N,N′-(Pyromellitoyl)-bis-L-leucine Segments

In this study, the goal was the preparation, characterization, and surface morphology of poly(amide-imide)/TiO₂-citric acid nanocomposites (PAI/TiO₂-CA NCs). Owing to the high surface energy and tendency for agglomeration, the surface of TiO₂ nanoparticles was modified with citric acid. Then poly(amide-imide) was synthesized by direct polycondensation reaction of N,N′-(pyromellitoyl)-bis-L-leucine diacid with 4,4′-diaminodiphenylmethane by triphenyl phosphite and tetra-n-butylammonium bromide as a green medium. The attained polymer and modified TiO₂ nanoparticles were used to prepare PAI/TiO₂-CA NCs through ultrasonic irradiation. The resulting PAI/TiO₂-CA NC was characterized with FT-IR spectroscopy, X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, and thermogravimetric analysis.     

高效液相色谱-电感耦合等离子质谱法分析海洋沉积物中有机锡的形态

建立了高效液相色谱-电感耦合等离子质谱(HPLC-ICP-MS)测定海洋沉积物中二丁基锡(DBT)、三丁基锡(TBT)、二苯基锡(DPhT)及三苯基锡(TPhT)的形态分析方法。通过改变流动相组分比例,使4种有机锡达到基线分离。比较不同提取方法对标准参考物质PACA-2中有机锡的提取效率。以V(乙腈)∶V(H2O)∶V(乙酸)=55∶33∶12(含5%三乙胺,pH 3.0)为提取剂时,超声提取效率最高(>91.5%),其加标回收率均大于96%。本方法对DBT,TBT,DPhT和TPhT的检出限分别达到0.7,0.75,0.45和0.4μg/kg。对浓度范围为0.5～100μg/kg有机锡混合标准溶液进行测定,4种有机锡回归系数均大于0.998。利用本方法对几种海洋沉积物样品和海产品中的有机锡进行测定,在部分沉积物样品中检测到了DBT和TBT,部分海产品中测到了少量TBT和TPhT。     

超声搅拌化学浴沉积法制备大颗粒和致密的CdS薄膜

采用超声搅拌化学浴法(UCBD)在SnO2:F透明导电玻璃衬底上制备了CdS薄膜.研究了退火和CdCl2处理对UCBD-CdS薄膜的表面形貌、晶体结构和直接带隙的影响,比较了沉积时间对UCBD-CdS薄膜中CdS聚集体颗粒大小和堆积致密性的影响.结果表明,CdCl2处理可使CdS聚集体中的小颗粒重新熔合在一起,但CdS聚集体的大小并没有改变.在UCBD-CdS薄膜的沉积过程中,CdS薄膜的横向和纵向生长速率之比会随着沉积时间的不同而改变,且沉积时间是获得大颗粒的CdS聚集体和致密的UCBD-CdS薄膜的重要影响因素.当沉积时间为40min时,获得的UCBD-CdS薄膜较致密,CdS聚集体的大小为180nm,膜厚为80.8nm,适合作为薄膜太阳电池的窗口层.     

Fast Electrochemical Characterization of Historical Glasses Using Carbon Screen‐Printed Electrodes and Ultrasonic Assisted Sampling

A new method for lead oxide (PbO) analysis in glasses, using a carbon screen printed electrode (SPE) is proposed. A suspension of the powdered glass sample in nitric acid is prepared using an ultrasonic probe, 100 µL of slurry are deposited on the SPE and the voltammetric measurement is carried out. Structural information of PbO in the glass matrix is obtained by CV. Lead quantification is performed by DPV. In the best conditions a LOD of 2.30 wt% of PbO was obtained. The method has been applied with good results in the analysis of historical glasses samples.     

Sulfur removal from bauxite water slurry (BWS) electrolysis intensified by ultrasonic

Effects of ultrasonic on desulfurization ratio from bauxite water slurry (BWS) electrolysis in NaOH solution were examined under constant current. The results indicated that ultrasonic improved the desulfurization ratio at high temperatures because of the diffusion and transfer of oxygen gas in electrolyte. However, due to the increase in oxygen gas emission, ultrasonic could not improve the desulfurization ratio obviously at low temperatures. Additionally, the particle size of bauxite became fine in the presence of ultrasonic, indicating that the mass transfer of FeS₂ phase was improved. According to the polarization curves, the current density increased in the presence of ultrasonic, indicating that the mass transfer of liquid phase was improved. The apparent activation energy (AAE) of electrode reaction revealed that ultrasonic did not change the pathway of water electrolysis. However, ultrasonic changed the pathway of BWS electrolysis, converting indirect oxidation into direct oxidation. The AAE of BWS electrolysis in the presence of ultrasonic was higher than that in the absence of ultrasonic. And the low AAEs (less than 20 kJ/mol) clearly indicated the diffusion control during BWS electrolysis reaction.     

Measurement of micro weld joint position based on magneto-optical imaging

In a laser butt joint welding process,it is required that the laser beam focus should be controlled to follow the weld joint path accurately.Small focus wandering off the weld joint may result in insufficient penetration or unacceptable welds.Recognition of joint position offset,which describes the deviation between the laser beam focus and the weld joint,is important for adjusting the laser beam focus and obtaining high quality welds.A new method based on the magneto-optical(MO)imaging is applied to measure the micro weld joint whose gap is less than 0.2 mm.The weldments are excited by an external magnetic field,and an MO sensor based on principle of Faraday magneto effect is used to capture the weld joint images.A sequence of MO images which are tested under different magnetic field intensities and different weld joint widths are acquired.By analyzing the MO image characteristics and extracting the weld joint features,the influence of magnetic field intensity and weld joint width on the MO images and detection of weld joint position is observed and summarized.     

基于ABAQUS的微细电火花超声振动主轴 仿真研究*

微细电火花技术凭借自身的特点和优势,在航空航天、医疗器械等领域发挥着重要的作用。超声振动辅助电火花加工在传统电火花加工中引入超声振动,加工精度和加工效率明显提高。作为核心部件,超声振动主轴的设计尤为重要。但传统设计过程,大大延长了研发周期和增加了成本,,因此,采用仿真方式进行研究具有重要的意义。本文对设计的微细电火花超声振动主轴的进行了仿真研究,通过ABAQUS进行了模态分析和谐响应分析,得到了超声振动主轴的谐振频率和输出振幅等参数。超声振动主轴的测试实验验证了仿真结果的正确性。     

Optical characterization of polycarbonate: Influence of additives on optical properties

In laser transmission welding of thermoplastics the optical properties of the joining parts determine the quality of the welding result. Especially, the scattering of laser radiation in the transparent welding part has an impact on weld seam properties. This scattering is caused by additives. For polycarbonate (PC) with different additives the transmittance, the reflectance and the collimated transmittance are measured with a UV‐VIS‐NIR spectrometer. From this data, the optical properties, such as scattering coefficient, absorption coefficient, and anisotropy factor are calculated. The calculations are made with the aid of the four‐flux model of radiation transport in the diffusive approximation. The results show that the additives have a significant influence on the scattering coefficient. For most additives under consideration the scattering is forward directed, which means that most of the radiation is transmitted into the absorbing welding part. However, the power density distribution of the transmitted radiation may differ significantly from PC without additives. So, the weld seam may also differ due to different additives. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 451–455, 2010